easiPart T HD 12"
EasiPart T heat defiant topper transforms fine or thinning hair by adding density and body. This voluminous topper has a wider T-shaped base for more all-over coverage, and larger polyurethane perimeter allowing easier application of Tape ‘N Go or adhesive. Available in 12 and 18 inch lengths.
easiPart T HD 12"
SPECIFICATIONS
Item Number:
390
Color Shown:
12FS8
Hair Type:
Heat Resistant Synthetic
Base Dimension:
(W) 3" - 7.25" x (L) 6.75"
Collection:
Toppers
Application Method:
Clip In
Length:
12"
Weight:
3.3 oz
Base Design:
Single Monofilament with a PU Perimeter
EASIPART T
WELDED MONOFILAMENT Allows multi-directional parting while providing the appearance of natural growth
PU COATED MONOFILAMENT For use with adhesive if needed
PRESSURE SENSITIVE CLIPS To clip into hair if not using adhesive
HD | Heat Defiant Care
WE RECOMMEND WASHING YOUR ALTERNATIVE HAIR EVERY 6-8 WEARS
CLEANSE & CONDITION
• Before washing, gently remove any tangles using your Jon Renau Wide Tooth Comb ONLY
• Wet hair completely using cool running water
• Gently lather the hair with a small amount of Jon Renau Synthetic Shampoo, making sure that the hair is traveling in the same direction. DO NOT rub hair; this will cause tangling
• Rinse thoroughly under cool running water until water runs clear
• Wrap wig or hairpiece in a towel and gently pat dry
• Gently detangle hair using Wide Tooth Comb
• Spray with Leave-In Conditioning Spray (3-5 pumps) keeping away from base
DRY & STYLE
• Allow wig or hairpiece to air dry naturally by placing on a plastic or wire wig stand. Do NOT blow dry
• Air drying your wig will give the best results. The fiber will dry fastest; be sure the cap is completely dry before wearing, storing, or displaying
• Apply HD Smooth Detangling Spray, (3-5 pumps) focusing on the bottom half of wig or hairpiece. Gently comb through using your Wide Tooth Comb
• ONLY the Jon Renau wide tooth comb is used on your HD fiber. Other tools will cause frizzing/tangling
• HD fiber can withstand heat up to 350° F, however, Jon Renau recommends working at 270°-280° F
• It is recommended to use professional grade heat styling tools with digital temperature settings to control heat
CURL & FLAT IRON
• Heat your curling or flat iron to 270°-280° F
• Using your Jon Renau Wide Tooth Comb, gently comb hair free of tangles
• Starting at the nape, take ½ inch-1.5 inch sections of hair (smaller sections=tighter curls, larger sections=looser curls)
• Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)CURL
• Gather hair into curling iron, smooth through to the ends. Roll iron up towards base of wig or hairpiece, staying 1-2 inches away
• Hold for 10-15 seconds, then turn the tip of iron toward the ground and release curl into palm of hand
• Holding curl in one hand, gather up towards base and secure curl with a small metal clip (like a pin curl)
• Allow curl to cool completely (about 5 minutes); remove clip and let curl hang naturallyFLAT IRON
• Starting at the nape, take ½ inch-1.5 inch sections
• Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)
• Slowly smooth flat iron down through ends; keep hair smooth by following behind the flat iron with your Wide Tooth Comb
• Allow hair to hang naturally and cool completelyTIPS
• All synthetic fibers can tangle and frizz with wear. It is important that the frizz is corrected early to avoid permanent damage to the fiber. Use your flat iron to smooth any frizz before washing
• We recommend using HD Smooth Detangling Spray with a Wide Tooth Comb DAILY to detangle your HD wig. This is especially important with the mid-length to long length HD wigs or hairpieces
• To add texture and definition, use a small amount of Piece Out Contour Fiber Crème and apply using fingertipsTo see the color options listed for this product, please go to the Hair Color Options here. Make sure to reference the color options available for this product below.